Wednesday, May 18, 2011

SSR 15 Inch Wheel Advertisement! - Casablanca Eight

Just saw this on Monkeymagic's blog!

This is the first ad I've ever seen for the Casablanca Eight wheel.

From Dirty S30


Look familiar??

From Z2


Love this.

Thanks for posting man!

Bad Dog RLCAs

I know I know I really wanted to get that ill set of Rear Lower Control arms that Techno Toy Tuning makes for the 240z, but this time my budget wouldn't permit.

But luckily, a friend of mine John that runs Bad Dog Parts (the frame rails guys), let me take his set that he used on his 240z race car!

From ZCCNE Charity Inspection


You can see the LCAs installed here.

From ZCCNE Charity Inspection


You can also see the bottom of the custom fuel cell that they traded me and how they ran their fuel pump setup.

From ZCCNE Charity Inspection


John and Pete are the guys that built and race this car, and I gotta say that they are some of the nicest guys I've ever met. They also have an awesome collection of stuff that somehow ends up getting installed in my car! :D

So here are the RLCAs.

From Z2


As you can see they are stock LCAs, but are in much much better condition (metal wise), than my stockers.

From Z2


And they came with the eccentric RLCA bushings!

From Z2


If you look at that picture closely (and through all the dirt), you can see that the metal bushing is off center. This allows you to tune the camber AND toe settings on a stock set of lower control arms!

Very cool. And since I can't afford the blinged out T3 set, I can't think of a better set of stockers to run. 'Cause if they were good enough for a race car, then they are good enough for me... For now. lol

Check out Bad Dog Parts here:

Monday, May 16, 2011

Engine rebuild - pt.3

With the short block assembled, it was time for head installation.

From Z2


I used the Felpro 1mm head gasket so I could get my target 9.2:1 compression ratio.

Note: Maxima N47 Head, and a stock N42 L28 short block and rotating assembly, with a 1mm Felpro head gasket makes for a 9.2:1 comp ratio.

I cleaned up the gasket surfaces on the head and the block by using an extra fine silicon carbide wet/dry sand paper and air tool oil as a lubricant. This helps make sure that there aren't any traces of old gasket left on the surface. I recommend that you do this if you do not have the surfaces professionally machined.

From Z2


I also wire brushed out the combustion chambers using WD40 to help break up the carbon deposits. Worked great! At this time, make sure you line up the cam thrust plate timing dowel with the top center timing mark (it will be obvious when you look at it).

From Z2


With the block dowels and head gasket down, I carelessly tossed the head onto the block, making sure to align everything perfectly.

Be absolutely sure that the first piston is at exactly top center.

From Z2


After searching for almost an hour, I finally found my head bolts and thumb tightened them into their holes.

From Z2


Then, according to the factory specified torque procedure, I tightened it all down.

From Z2


Then we installed the crank side timing sprocket. Make sure when you install this, that the timing mark is visible, or you will have to take it back off and flip it over (me).

From Z2


Then the chain tensioner, guides, and cam sprocket get installed. Make sure that you install the #1 cam hole on the cam thrust plate dowel. Then make sure that the "bright links" on the timing chain install on both of the #1 sprocket teeth.

Like this.

From Z2


From Z2


Head and timing system installed.

From Z2


Next up is the timing cover, oil pump, water pump, distributer, all the gaskets and seals, and then the oil pan and valve cover!

Wednesday, May 11, 2011

Engine rebuild - pt.2

Now that the block has been prepped, it's time to start the actual build process.

To help me with this, I had to call up my nerdiest friend, Chris.

From Z2


We started by pulling off all of the old piston rings. Be careful when doing this as all the heat from the motor will have made them brittle and prone to breakage when bent.

From Z2


Once all of the rings were off I inspected the ring lands to make sure that they were reusable and they all checked out fine.

From Z2


Next we installed the new piston rings.

From Z2


Make sure that you install the rings with the gaps facing the correct direction as advised by whatever rebuild reference you are using. The point here is so that none of the gaps are in the same place.

From Z2


Next we moved on to the crankshaft main bearings.

From Z2


We cleaned the block several times with Brakleen to make sure that it was nice and free of debris.

From Z2


Then we installed the bearings making sure that they all ended up in their proper locations.

From Z2


So fresh and so clean.

From Z2


Next we lubed up the rear of the crankshaft and installed the rear main seal onto the crank. Nissan says that this is incorrect, but they are chuckleheads and this way is best.

From Z2


Then, we lubed up all of the bearing journals with 20/50 motor oil and laid the crankshaft into the bearings, being extra careful not to ding the rear main seal or the journals on the crankshaft on the way in.

From Z2


The first cap to install is the rear main cap. This slides into the void shown below very snuggly. We ran 1" of SuperBlack RTV on each corner of the block to ensure a tight seal.

From Z2


Once the cap is installed, we slid the rubber seals, and shim nails into the RTV filled cap voids.

From Z2


Then we installed the rest of the caps, starting with the front and working our way back to the rear main. After they were all installed, we followed the proper torque order and torqued them all to the recommended 40ft/lbs.

From Z2


Now that the crankshaft is installed, it is time to install the pistons.
We installed the connecting rod bearings into the rods, and removed the end caps.
Then, using a piston ring compressor, we cranked the rings down to prep them for installing into the block.

From Z2


We inserted the piston into the block rod first until the piston ring compressor stopped on the gasket surface of the block. Then, using a shop towel and the wooden end of a hammer, we banged the piston into place being careful not to lose the connecting rod bearings from below, or ding the crankshaft journals. It is also a good idea to spin the crank until the piston that you are installing would be at top of its stroke. That way the connecting rod can seat correctly on the crank journal.

From Z2


Once the piston was in, we turned the block on it's side to thumb tighten the rod nuts.

From Z2


Repeat these steps for all six pistons.

From Z2


Flip the block and torque all of the connecting rod bolts to spec and you're done.

From Z2


Rotating assembly assembled.

Monday, May 9, 2011

Engine rebuild - pt.1

So I started rebuilding my L28 this weekend and can honestly say that without this book, I would be straight up guessing at what to do.

From Z2


If you want to rebuild an L series motor, you can do no better.

Luckily, I had the foresight to bag and mark all of my nuts and bolts from the disassembly so it was very easy to take inventory before getting started.

From Z2


I pulled my L28 block out of storage and gave it a good cleaning before doing anything. Brakleen loves me.

From Z2


My first order of business was to hone my cylinder bores.
I strongly recommend watching a video on how to do this to get an idea of the speed of plunging and spinning that is required.

From Z2


As for honing oil, everyone has a different opinion. Some say kerosene is the best, some say to use a mix of 20w motor oil and kero, some say to never use motor oil, etc etc..

I found one site that said that they had the best results from using WD40. So I picked that one cause it was easy. :)

From Z2


Attach the spring loaded cylinder hone to your favorite drill and get to work, making sure that you clean the bores thoroughly, and keep them well oiled. I had bad results from honing while the block was upside down. I recommend that you hone with the block right side up.

From Z2


If all goes well, and you are a master of doing things, your hone job will be perfectly crosshatched. A quick google will show you that machine shops can get a much nicer cross hatch than this, but since I completed this job for about $20 (including the WD40), I am happy with it.

From Z2


Next you have to clean the bores three times with WD40 and Brakleen and check the bores thoroughly for any deep scratches or anything at all that you can catch your fingernail on. If you can catch your finger nail on it, it's no good and you have to re-hone it.

From Z2


Sweet.


Next up is test fitting and gapping your piston rings. I bought mine from Rock auto and got the cheapest ones I could find. The "Economy ring" by Sealed Power.

From Z2


They ship the rings in separate compartments because each ring is different, and needs to be an exact length for each ring's specific job and heat tolerance requirements.

From Z2


Keeping tabs on which rings will be where in relation to the piston and their specific cylinder bores, you have to test fit them in the block.

From Z2


The top or primary compression rings need to have a total ring gap of .014 inches (0.36mm). With the use of the proper feeler gauge, I was able to determine that my "Econo" rings and my Craigslist L28 were exactly perfect with all rings on all bores.

From Z2


I continued this process with the bottom or secondary compression rings. They required a total ring gap of .012 inches since they are subject to less heat and subsequent expansion, they require less overall clearance tip to tip.

Every single ring in every single bore measured out absolutely perfectly (lucky mofo), so I did not have to shave any of my rings.